The Shark Steam Mop is perfect for a clean and shiny home. It’s easy to use and requires only 20 minutes to heat up. However, it sometimes malfunctions when the water runs out or when water is left in the tank after cleansing.
If your Shark steam mop isn’t working properly, there are a few things you can do to troubleshoot the issue. This article will go over a few common issues and how to resolve them.
1. Shark Handheld Steamer Not Steaming
Shark handheld steamer not steaming? It’s a common frustration your Shark handheld steamer is giving you a hard time and you can’t figure it out.
Here are possible reasons：
1. The Shark handheld steamer is too cold.
2. There is a clogged steam cord or the heating element is not engaged.
3. The steam head of your Shark handheld steamer has a kink in it.
4. The steam head of your Shark handheld steamer is loose or the steam cord is not plugged in properly.
- Solutions:
1. Turn on the Shark handheld steamer and press the steam button for about 12 seconds.
2. Press the steam button for about 5-6 seconds to re-heat the steam head if it is cold.
3. Place your hand under the steam head to see if there is a kink in it because clogging can occur from water splashing up into it when you are steaming hard surfaces that are not wet
4. If the steam head is loose, use your fingernail to turn and tighten the steam head to rotate it so that it will fit tightly into the steam cord.
2. Shark Genius Steam Mop Not Steaming
The Shark Genius Steam Mop is one of the newest and most innovative home cleaning products in a long time, but it has its share of flaws.
One issue some consumers have is that the steam cleaner does not always produce enough steam to clean large areas like a kitchen or living room at one time.
Here are possible reasons for the Shark genius steam mop not steaming:
1. Your water reservoir is empty, or it may be too full.
2. Your Shark genius steam mop nozzle is clogged with dirt and debris.
3. If your Shark genius steam mop model includes an extension wand, you may have it plugged into the wrong area on the cleaning head.
4. Your Shark genius steam mop is broken and will need to be replaced by a new one, or taken in for repair by an authorized service provider.
- Solution:
Plug Shark Genius Steam Mop In.
1. Make sure the cord is plugged into a wall outlet and out of the way, and that the steam cleaner is turned on.
2. Make sure it’s in the right outlet and on the “right” side of the wall for where you want to use it.
3. Insert Steam Cleaner Body Wand into Steam Cleaner Head.
4. Make sure both pieces are connected properly to the steam cleaner before you turn it on.
3. Shark 2 in 1 Vac Then Steam Not Steaming
Shark 2 in 1 vac then steam not steaming Reasons:
1. The tank is not connected to the power.
2. The tank is not installed properly.
3. The tank switch does not work and/or does not turn on the vacuum motor mode.
4. The wall outlet or plug switch is broken or has a bad crimp connection to avoid arcing or sparking electrical current in your home, causing fires and electrical hazards which can cause serious injury, bodily harm, and death, including burns and explosions.
5. The cord or plug has been damaged by water, bleach, cleaning products, or other corrosive substances.
- Solutions:
1. Make sure the vacuum tank is powered on (if necessary, press the power button).
2. Make sure the Tank Switch is in the ‘ON’ position (if necessary, press down on the Tank Switch until it snaps into position).
3. If none of these solutions solves your problem, you may have an electrical short that should be resolved by a qualified technician.
4. Make sure that the electrical cord is connected properly.
5. Make sure that there is not a short in your electrical cord or the power plug, by testing for an open circuit with a voltage tester.
4. Shark Steam Mop Not Heating Up
The most common problem with the steamer is generally before you begin cleaning, the machine does not heat up.
This issue is often caused by using water that is too hot or by using too little water.
- Solutions:
The solution to this issue is to make sure that the water is hot enough to start steaming and then add more water when needed.
5. Shark Steam Mop Making A Clicking Noise
Here are the possible reasons and fixes:
1. The gears might need to be oiled. You can easily fix this issue by turning off the machine and then opening it up.
2. If the machine is simply making a clicking noise, it could be due to the fact that the gears are not moving properly. You can check this by scrubbing them lightly with a fine toothbrush.
3. If the problem is still not solved, you can call for the professional help from your local store or you can look for alternatives at a different store if none of these work for you.
6. Shark Steam Mop Not Turning On
The Shark steam mop may not turn on due to the following reasons:
1. The machine might need to be charged.
2. The fuse of the machine might have blown and you need to replace it immediately.
3. If the problem is still not solved, you can call for help from your local store or you can look for alternatives at a different store if none of these work for you.
- Solutions:
1. You need to wait for 2 minutes before turning on your machine as stated above (2 minutes).
2. The fuse might have blown and you need to replace it immediately.
3. If the problem is still not solved, you can contact professional help from your local store or you can look for alternatives at a different store if none of these work for you.
7. Shark Steam Mop Leaking Water
If your shark steam mop is leaking water, there are a few possible reasons.
1. The most common reason is that the water tank is not properly sealed. Make sure that the tank is properly seated and that the O-ring seal is intact.
2. If the problem persists, try replacing the O-ring seal. Another possibility is that the pump is not working properly.
3. Check to make sure that the pump is receiving power and that the inlet and outlet valves are open. If the problem persists, try replacing the pump.
4. If your mop is leaking from the bottom, it is likely that the floor nozzle gasket is damaged or missing. Replace the gasket and/or nozzle as needed.
The similar problem you may encounter:
8. The Shark Steam Mop Is Clogged
The shark steam mop might clog due to one of the following reasons:
1. The machine might not have been used properly or cleaned properly before use.
2. The floor attachment may have been disconnected and needs to be reconnected.
3. The debris has stuck to the machine and got clogged in it.
4. You need to stop using the machine immediately if it is not clogged but still does not function as per need and then call for the professional help from your local store or you can look for alternatives at a different store if none of these work for you.
- Solutions:
1. The chief reason behind the clogging of the machine is the debris that is stuck in it. In order to fix this issue, you need to clean your floor attachment properly before use.
2. The machine might not have been used properly or cleaned properly before use.
3. You need to stop using the machine immediately if it is not clogged but still does not function as per need and then contact the professional help from your local store or you can look for alternatives at a different store if none of these work for you.
9. Shark Fabric Steam Cleaner Clogged
1. The most common cause of a clogged Shark steam mop is debris in the mop head. Your Shark steam mop works best if your cleaning solution flows smoothly with minimum interruption. This means keeping the rubber squeegee blade clean and free of hair, dirt, or dust.
2. Another common cause is a thermostat malfunction. The thermometer registers when your mop head reaches a certain temperature, which usually means that it’s time to rinse and/or refill your cleaning solution.
You’ll find a mark on the side of your mop head where this temperature is indicated, and a window on your handle where you can see the actual temperature.
This malfunction makes the mop head overheat, which it interprets as a clog. This may lead to the thermometer shutting down completely, or simply making it so that you need to rinse and refill your cleaning solution more frequently.
- Solutions:
1. Rinse your mop so that the last cleaner hasn’t been sitting around for too long. This is especially important if you use a stubborn cleaning solution (like lemon juice) that dries out hardware and rubber parts, like the squeegee blade of your Shark steam mop.
2. You can also rinse with warm water to ensure the most thorough clean. If you are still having issues, try to remove the debris from your mop head. If this doesn’t help, try restarting your mop.
Do this by turning it on and off while pressing the steam button on the handle. Your mop may need to power down a few times before it is at its best again.
10. Shark Steam Mop Blinking
Shark steam mop blinking is usually caused by an issue with the water tank and can be solved in one of two ways.
Either you need to manually remove the water tank and drip a little bit of water into it so that there is enough pressure to run through the system, or you can add more water to the tank.
- Solutions:
Shark steam mop blinking can also be caused by a power surge that has affected your Shark steam mop.
To troubleshoot, first turn off your machine and unplug all cables from it. Wait 30 seconds and plug the machine back in and see if the problem persists. If it does, then you will want to contact a licensed electrician for assistance
So, buying a long-lasting steam will save a lot of energy! Or may you need to change a new on if all the methods can’t work for you.
Here are our recommendations: Shark S7001 Mop, Scrub & Sanitize at The Same Time! The automatic scrubbing mop head with rotating pads delivers over 150 scrubs per minute, providing an effortless glide and a smooth cleaning experience—the pads do all the work.
Click here to see the discount!
Conclusion
Shark steam mop is a very useful appliance. Its usage makes cleaning the house easier and gives better results with less effort. The best way to use a shark steam mop is to keep it clean and empty.
This was the very first shark designed for cleaning your house. The steam mop provides high quality and amazing performance as per all the expectations of an efficient cleaning appliance
